ScreenshotGoogleEarth1-1

Roof Measurement Report for RESIDENTIAL Roofs

The Roof Measurement Report provides a detailed analysis of your roof layout and all the critical dimensions. Our full color report provides the detailed lengths, pitch and areas of every surface plane and edge. This report saves your time and enables accurate roof estimates for a roof repair or replacement. This is a professional grade report used for use by licensed roofing contractors or insurance companies. You will receive the report in .PDF format by email within 1-3 days.

How to Manually Measure a Roof

To manually measure a roof without the help of aerial measurement reports, you must visit a job site and climb onto the roof to take precise roofing measurements by hand. Here are the 6 steps to get a manual roofing measurement.

 
  1. Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area.
    Example: Plane 1 (A x B): 50’ x 20’ = 1000 sq ft
    Plane 2 (A x C): 50’ x 20’ = 1000 sq ft
  2. Note any skylights, chimneys or other parts of the roof that would not require materials. You can subtract those measurements from your total area.
  3. Add together the calculated square footage of each surface to get the figure for total square footage of the roof.
    Example: Plane 1 (1000 sq ft) + Plane 2 (1000 sq ft) = 2000 sq ft
aerial roof measurement
  1. After determining the total square footage of the roof, you must calculate the pitch of the roof. Measure the vertical distance (rise) over a 12 inch horizontal segment (run).
    Example: The rise of this roof is 5”.
  2. Write down these numbers as the vertical measurement listed first and the horizontal measurement recorded second so you can find rise over run.
    Example: The rise over run of this roof is 5” over 12”.
  3. When you have the total square footage and rise over run of the roof, you can calculate the roof squares to determine how much materials are needed to cover the roof. To calculate the number of squares on a roof, you need to divide its total square feet by 100.
    Example: 1000 sq ft / 100 = 10 squares

With those roofing measurement figures, you can then estimate the roofing supplies needed for a job.

How do you find the sq ft of a roof?

To find your roof’s total square footage:
  1. Measure the length and width of each plane on the roof (including dormers) then multiply length times width.
  2. Add the square footage of each of the planes together.

How do I estimate roofing costs?

According to Sky Roof Measure, the typical range for roof replacement costs is between $5,100 and $10,000, but roof replacement can be as low as $1,200 or as high as $30,000. Many roofing companies will charge between $3.50 and $5.00 per square foot.

What is a fair price per square for roofing?

A replacement could be as low as $1,200 or as high as $30,000. With that said, on average, most roofing companies will charge somewhere between $3.50 and $5.50 per square foot, or $350 to $550 per square (100 square feet) to install or replace an asphalt shingle roof.

How much does it cost to tear off and replace a roof?

Most homeowners can expect the average cost to tear off and replace a roof to be around $12,000 to $15,000. This price is based on a home with 3 bedrooms, 2 bathrooms, a walkable roof pitch, a little roof complexity, and architectural asphalt shingles.

What is the cheapest way to replace a roof?

While asphalt is the cheapest roofing material, there are 3 different types of asphalt shingles that vary in price and affect how much you’ll spend on your roof replacement. 3-tab shingles are the cheapest of the 3 types of asphalt shingles and are a great option for a tight budget.

How many times can you overlay a roof?

Installing new roof shingles over old effectively doubles the weight of the roofing, so you have to make sure your roof structure can handle the extra load. That’s also why building codes commonly limit re-roofing to no more than two layers.
 
Screen Shot 2021-08-12 at 6.38.35 PM

Aerial Estimation | Aerial Roof Measurements

What is aerial roof measurements?

Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area. Note any skylights, chimneys or other parts of the roof that would not require materials so you can subtract those measurements from your total area.
 
The Roof Measurement Report provides a detailed analysis of your roof layout and all the critical dimensions. … This report saves your time and enables accurate roof estimates for a roof repair or replacement.

How do I estimate roofing costs?

According to SkyRoofMeasure, the typical range for roof replacement costs is between $5,100 and $10,000, but roof replacement can be as low as $1,200 or as high as $30,000. Many roofing companies will charge between $3.50 and $5.00 per square foot.

How much does a 1000 sq ft roof cost?

Roof Size and Pitch

A new roof on a 1,000-square-foot house costs an average of $4,000 to $5,500 while the cost to replace a 3,000-square-foot home’s roof can rise to an average of $11,200 to $16,000.

How much would a 1200 sq ft roof cost?

Average cost to replace a roof based on house size:

1,200 square feet: $4,500 to $6,500. 1,500 square feet: $5,500 to $8,000. 1,600 square feet: $6,000 to $8,500.

How much does it cost to roof a 2200 sq ft house?

 A new asphalt shingles roof for a typical 2,000 to 2,200 square foot single-family house can range in price from $9,500 to $18,700 fully installed, including the tear off and disposal of the old roof (up to two layers).

Confidence In Your Bids & Bottom Line.

Our aerial roof measurement reports are drafted by expert CAD technicians and reviewed by a quality assurance professional, certifying absolute data accuracy on every report. Precision is paramount at Sky Roof Measure, and that’s how we guarantee a 95% or better accuracy rate on every plane, eave, rake, ridge, hip and valley. Be confident in your bids, and submit estimates that align to your profit goals.
roofer

Roofer Reports By Sky Roof Measure

What is a roofing report?

A Roof report is a visual inspection and report on the condition of the roof covering to the main property, rainwater goods, chimney stacks, soffits and fascias and any other roofs associated with the property.
 

What is a roof inspection report?

Roof inspection reports come in as many formats as there are roofing companies. … It can detail the roof’s age, manufacturer, information about the slope and height, roof type, etc. Inspections will also typically include replacement estimates for the whole roof, even if replacement isn’t in the scope of work involved.

How long does a roof estimate take?

The actual estimate itself will take on average 30 minutes to an hour. You don’t have to be present but it is advisable in case the roofing contractor needs to see inside the house for a leak. After the estimate is complete, it may take up to ten days for the contractor to get you the roofing quote for the job.

Roof Measurement Report 

The Roof Measurement Report provides a detailed analysis of your roof layout and all the critical dimensions. … This report saves your time and enables accurate roof estimates for a roof repair or replacement. This is a professional grade report used for use by licensed roofing contractors or insurance companies.

Sky Roof Measurement Reports use the best of the industry’s Proven off-the-shelf software and available aerial imagery to provide Roofers, Contractors, Insurance Carriers, and Adjusters a Customized, Detailed, and Accurate Roof Measurement Reports. Never miss another opportunity to provide an estimate due to distance, location, and weather conditions.

How to calculate roofing material?

To estimate roofing materials, start by finding the total square footage of the roof and divide the number by 100 to determine the number of “squares” in the roof. Since it takes 3 bundles of shingles to cover a square, plan to purchase 3 bundles for each square. Then, add 10% to the number to account for waste.

Measure a roof safely

Without the proper training and equipment, it isn’t recommended for homeowners to climb on their roofs.  If you want to get the project started yourself, opt for the safer alternative that will save you time and keep you safe by ordering an aerial roof measurement report.   

 
526d7763ceb1bfe910aebc65bdf212c0--dormer-roof-dormer-ideas

Roof Measurements – How to Get a Roofing Measurement USA

To find your roof’s total square footage:
  1. Measure the length and width of each plane on the roof (including dormers) then multiply length times width.
  2. Add the square footage of each of the planes together.

WHAT YOU’LL NEED TO MEASURE A ROOF:

  • Ladder
  • Measuring Tape
  • Calculator
  • Pen/Pencil
  • Paper

roofer

Square Footage

  1. The first thing you’ll need to measure is the square footage of your roof.
  2. Position your ladder at the corner of one of your roof planes to determine the length.
  3. Extend your measuring tape as far as you can along the length of your roof and mark the area.
  4. Move your ladder down to the next section. Beginning with where you marked the first measurement, measure the next section.
  5. Continue measuring the length of your roof until you’ve covered the entire length area.
  6. Write down the final measurement.
  7. Next, you’ll want to measure the width of your roof plane. (Depending on how high your roof is, you may want to be up on it to take this measurement.)
  8. Use your ladder or your feet to measure the entire width of your roof plane.
  9. Write down the final measurement.
  10. Continue steps 1-9 on each of your roof’s planes.
  11. Multiply the length and width of each plane to get the square footage. Then, add all of your square footage measurements together to get the total square footage of your roof.

Slope

  1. You’ll also need to measure the slope, or angle, of your roof.
  2. To do this, position your ladder near the top point of your roof.
  3. With your measuring tape, measure vertically from the top point to the bottom point of your roof. (This is also called the rise.)
  4. Repeat this over 12 inches, then place the measurement over “12”. (For example: If your rise is 4 inches over 12 inches, then your slope measurement is 4/12.)
Calculating How Many Tiles You Need for Your Roof
  1. A ÷ X = D (Number of Tiles Needed for One Row Across the width)
  2. C ÷ Y = E (Number of Rows Needed)
  3. D x E = F (Number of Tiles Needed for One Side of the Roof)
  4. F x 2 = Total Number of Tiles Needed.

Can you measure a roof from the ground?

If you’re planning work on a roof and don’t have the building plans, taking preliminary measurements from the ground allows you to approximate the roof area and estimate some costs. … But, you can measure a gable or flat roof from the ground with the help of an assistant.
 

How do you calculate roof battens?

Measure from the top of the lowest batten to the top of the highest batten, then divide this number by the maximum gauge recommended by the manufacturer, and round this up to the nearest whole number. This will tell you how many courses are needed to tile your roof.

How do you measure a roof on Google Earth?

  1. On your computer, open Google Earth.
  2. Search for a place, or select a location on the globe.
  3. On the left, click Measure. . …
  4. Click the map to set measurement points.
  5. To remove a point, on the right, click Undo .
  6. To complete your line measurement, double-click on your last point, or click Done .
 
Roof battens: Provide a breathable space allowing any condensation to be eliminatedIncrease the structural performance of roof truss systems. Enable roofing materials to be secured firmly to the roof. Assist with correct alignment of roofing sheets.

How many bundles of shingles do I need for a 12×12 roof?

Bundles. Asphalt shingles and most other roof shingles are typically available in bundles. For each roofing square or 100 sq ft, you’ll need three bundles of shingles.

How many bundles of shingles do I need for a 10×10 shed?

How many shingles would I need for a 10×10 Gambrel shed roof? – Quora. Well, I did the job myself and the answer is: 5 packs.
 
roof

Accurate Aerial Roof Measurements and Takeoff Report

The Roof Measurement Report provides a detailed analysis of your roof layout and all the critical dimensions. … This report saves your time and enables accurate roof estimates for a roof repair or replacement.

To find your roof’s total square footage:
  1. Measure the length and width of each plane on the roof (including dormers) then multiply length times width.
  2. Add the square footage of each of the planes together.

What is aerial measurement?

An Aerial Measuring System plane in the air. The Aerial Measuring System (AMS) is a rapidly deployable capability that can respond to all manner of nuclear incidents and accidents in the United States and overseas.

How do I calculate roofing materials?

To estimate roofing materials, start by finding the total square footage of the roof and divide the number by 100 to determine the number of “squares” in the roof. Since it takes 3 bundles of shingles to cover a square, plan to purchase 3 bundles for each square. Then, add 10% to the number to account for waste.
 
How to Calculate Roof Pitch in Degrees
  1. First, you need to measure the run of your roof. …
  2. Next, you need to figure out the rise. …
  3. Now, divide the rise by the run. …
  4. Then, divide 1 by your tangent.
  5. Finally, multiply this result by 180/π and you’ve calculated your roof pitch!

How do you measure a roof for a light?

Pretty simple, measure along the roofline either directly at the edge between two people on ladders, along the ground under the roofline, or while walking along the ground with a rolling measure under the roofline edge. These are all fairy precise ways of measuring for your project.

What are standard roof pitches?

What are common roof pitches? For a typical roof pitch to use for a traditional house, you should start with the 4/12 pitch cited above, but anything falling in the range between 4/12 and 9/12 is pretty common. If your pitch is lower, you will see it sporting a slight angle, hence the term low-slope roofs for them.

What does a 4/12 roof pitch mean?

A roof that rises 4 inches for every 1 foot or 12 inches of run is said to have a “4 in 12” slope. … The slope can be expressed numerically as a ratio. The slope ratio represents a certain amount of vertical rise for every 12 inches of horizontal run. For example, a “4 in 12” slope can be expressed as the ratio of 4:12
Estimate Roof Size

Metal Roofing Calculator

How do I figure out how much metal roofing I need?

Divide the length of your roof by the width of the metal. In our example we will use 24-inch standing seam roofing, so we will divide 360 inches by 24, which equals 15. This is the number of metal panels needed for one side of the roof.

How do you measure a roof for metal roofing?

Here’s our step-by-step guide for measuring the total roof area for installation:
  1. Step 1: Start by sketching out a top-down view of your home’s roof. …
  2. Step 2: Measure the length of your roof. …
  3. Step 3: Next, figure out the width of the metal that you’re installing. …
  4. Step 4: Repeat Step 3 for the other side of the roof

How much overhang should a metal roof have?

A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.
 
Install Metal Panels
Align the first metal roofing panel so that it overlaps the edging by 1/2 to 3/4 of an inch and is square to the roof line. Be sure the larger edge is laid so that the small edge of the next panel will overlap it.

Metal Roof Cost Per Square Foot

For many homeowners who are looking to install a metal roof on their house, cost is a huge factor.

As of 2022, the average price to install metal roofing is $5.97 to $9.85 per square foot.

Once you start researching various metal roof options, you will notice that there is a wide price range, depending on the type of metal and roofing system you want to install.

 

Lets take a closer look at how much you will spend on each popular metal roofing system:

Roofing TypeCost per sq. ft.Cost per square (100 Sq. Ft)Cost per sq.ft. installedInstall a 2,000 sq.ft. roof
Corrugated metal panels$1.75-2.5$175-250$4.25 – 6$8,500 – 12,000
Interlocking steel shingles$3.5 – $5$350- $500$8.75-11.5$17,500 – 23,000
Aluminum Shingles$4-6$400-600$9.5-13$19,000 – 26,000
Stone coated steel shingles$4.75 – 6.50$475-650$10 – 14$20,000 – 28,000
Steel standing seam$2 – 3.5$200-350$7.5 – 13$15,000 – 26,000
Aluminum standing seam$4-5.5$400-550$9.75 – 15$19,500 – 30,000
Zinc metal panels$8 – 11$800-1,100$15-20$30,000 – 40,000
Copper metal panels$10-13$1,000 – 1,300$17-22$34,000 – 44,000
 
aerial roof measurement

Roofing Calculator – How to Measure a Roof

How to Calculate Total Square Footage of Your Roof. To find your roof’s total square footage: Measure the length and width of each plane on the roof (including dormers) then multiply length times width. Add the square footage of each of the planes together.

How do I estimate the cost of a new roof?

According to SkyRoofMeasure, the typical range for roof replacement costs is between $5,100 and $10,000, but roof replacement can be as low as $1,200 or as high as $30,000. Many roofing companies will charge between $3.50 and $5.00 per square foot.

How do you calculate roofing wood?

Lets take the height of the roof as 3.5m and the breadth of plan plus overhang is 9m. Now divide by 3.6m to know the numbers of three” by 4” to purchase in market=24 pcs of three” by 4” required for rafters. PURLINS are the picket of two” by 2” or 50mm by 50mm we nail the roofing sheets on.

How do you calculate roof framing?

For example, if the slope is 4 in 12, and the run is 12 feet, the ridge beam height (M) will be 4 feet. The finished ridge beam height (Z) above the top of the wall will be (M) plus the Y Height. The formulas are: M = (R * X) / 12.

How much does a 1000 sq ft roof cost?

Roof Size and Pitch

A new roof on a 1,000-square-foot house costs an average of $4,000 to $5,500 while the cost to replace a 3,000-square-foot home’s roof can rise to an average of $11,200 to $16,000.

 
Cost to Tear Off & Replace Roof
House by Square FootAsphaltTotal Cost
1,200$4,320$6,276
1,300$4,680$6,799
1,400$5,040$7,322
1,500$5,400$7,845

How much should corrugated roofing sheets overlap?

Corrugated sheeting should always overlap by a minimum of one corrugation, this can be known as side laps. When overlapping corrugated sheeting its advised you use cladco lapping tape. For maximum sheet lengths in corrugated, we can supply 5m in a 0.5mm thickness and up to 6m length in the 0.7mm thickness.
 

Can you negotiate with a roofer?

You can always negotiate with your contractor on the price of a successful project before signing a contract. Discuss your budget with your roofing contractor. Agree that any unexpected project expenses will be presented in writing to help you remain within your budget.

Will roof prices go down?

Distributors and manufacturers are undoubtedly projecting higher prices as the year goes on. Again, even if the price drops some towards the end of the year or maybe early 2022, it’s safe to say it won’t drop below current market prices.
 
drone

What is a roofing take off?

A roof takeoff is a report that provides a full list of the materials needed to complete your roofing project. The term “takeoff” refers to taking each of the required materials off of the blueprint for a project. Generally, the list is generated from the final full set of a project’s architectural plans.

Understanding the Different Types of Roofers
  • Shinglers. …
  • Metal Roofers. …
  • Flat Roofers. …
  • Hot Roofers. …
  • Commercial Roofers. …
  • Residential Roofers. …
  • If A Roofer Recommends Shingling Over Already Existent Shingles, Say No. …
  • Does The Roof Require New Plywood Decking?

What’s the pitch of a roof?

Roof pitch (or slope) tells you how many inches the roof rises for every 12 inches in depth. An Example of a roof pitch would be a “6/12 pitch” which means that the roof rises 6 ” for every 12″ inward towards the peak (or ridge).

How do you estimate roofing?

To do this, measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane. Finally, calculate your roof’s total square footage by simply adding the square footage of each of the planes together.

Residential Roofing Estimating Process

Gone are the days for companies that still rely on climbing ladders and taking measurement manual by measuring tapes for residential estimation. This era is for techniques like that of eagle view and aerial-measurements that let you accurately measure a roof, saving time and money, even before materials are ordered.

The Contractors just tell SkyRoofMeasure the property’s address online through their website. The technicians pull high-resolution images for measurements and detailed reports that show details like length, pitch, area, and even more. With the mobile app, you can work with their interactive photo editor tool to mark areas of roof damage and other necessary details. You can combine multiple reports online with the aerial measurement reports.

Besides the aerial view, drone camera technology has even taken the roof measurement and estimation to the next level. You never have to ascend that ladder again, instead, a roof measuring drone camera and estimating software that you can carry in a hand-held tablet eliminates the need to climb onto the roof.

With more precise estimation and lower liability costs, you can seal more deals and generate more leads with improved safety and efficiency.

What type of roof is cheapest?

Asphalt is the cheapest of all roofing materials in the market and will last you between 15 to 30 years. This is the best option for homeowners facing budgetary constraints. It is also widely available and comes in a variety of colors.

What is the average price to tear off and replace a roof?

Around $12,000 to $15,000

Most homeowners can expect the average cost to tear off and replace a roof to be around $12,000 to $15,000. This price is based on a home with 3 bedrooms, 2 bathrooms, a walkable roof pitch, a little roof complexity, and architectural asphalt shingles.
garden_pavement

How many squares are in a 1000 sq ft?

How many shingles do I need for 1000 square feet?

Since there are twenty six shingles in a bundle of twenty year shingles (which is fine for starters and edges), divide the result by twenty six. For the number of ridge caps, multiply the length of the hip or ridge by twelve and divide it by five. This house is 1000 square feet. It requires 18 squares of shingles.

How many bundles of shingles do I need for a 1200 square foot house?

How many bundles of shingle to repair a 1200 square foot home with architectural shingles. Get quotes from up to 3 pros! Answered by SkyRoofMeasure: Depends on the shingle at the end of the day but I am going to assume 4 bundles per square. At that measurement, you need to figure on 52 bundles at a 10% waste.

How many squares is one SF?

100 square feet
 
One square is equal to 100 square feet. Examples where the unit is used are roofing shingles, metal roofing, vinyl siding, and fibercement siding products. Some home builders use squares as a unit in floor plans to customers.

How much does it cost to reroof a 1000 square foot house?

Roof Size and Pitch

A new roof on a 1,000-square-foot house costs an average of $4,000 to $5,500 while the cost to replace a 3,000-square-foot home’s roof can rise to an average of $11,200 to $16,000. Follow Us.

Price of Roofing Shingles Per Square Foot

Roof AreaCost of Shingles
1,000 square feet$910 – $1,100
1,500 square feet$1,400 – $1,600
1,750 square feet$1,600 – $1,850
2,000 square feet$1,810 – $2,110
Basic formula for square feet

Multiply the length by the width and you’ll have the square feet. Here’s a basic formula you can follow: Length (in feet) x width (in feet) = area in sq. ft.

How do I calculate shingles?

To estimate how many shingles you’ll need, first estimate the total square footage of your roof’s surface. To do this, measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane.

Are 50 year shingles worth the money?

It’s one of the most common questions people ask when it’s time to replace their roof: Are 50-year shingles worth the money? … In most cases, 50-year shingles won’t improve on resale value of a home over 25- or 30-year shingles.
 
roofer

How do you measure a roof for Blueprint shingles?

Here’s a step-by-step guide to measuring with blueprints:

  1. Open the app and select “Measure Your Roof.”
  2. Select “Sketch My Roof.”
  3. Retrieve your blueprint image by tapping “Load,” then selecting the source of the file, i.e., your email, Dropbox, etc.
  4. Select the blueprint you wish to measure.

How many shingles do I need for 1000 square feet?

Since there are twenty six shingles in a bundle of twenty year shingles (which is fine for starters and edges), divide the result by twenty six. For the number of ridge caps, multiply the length of the hip or ridge by twelve and divide it by five. This house is 1000 square feet. It requires 18 squares of shingles.
Price of Roofing Shingles Per Square Foot.
Roof AreaCost of Shingles
Roof AreaCost of Shingles
750 square feet$700 – $800
1,000 square feet$910 – $1,100
1,500 square feet$1,400 – $1,600

How many bundles of shingles do I need for 1700 square feet?

The shingles cover 33.3 sq. 57 bundles is a ft. 1,700 / 33.3 + 10% for trim.

Are 50 year shingles worth the money?

It’s one of the most common questions people ask when it’s time to replace their roof: Are 50-year shingles worth the money? … In most cases, 50-year shingles won’t improve on resale value of a home over 25- or 30-year shingles.

Is GAF or Owens Corning shingles better?

OC vs.

One area GAF Timberline Shingles really surpass Owens Corning is in their outstanding warranty offers. They are both pretty even when it comes to the standard roofing warranty, with 25 year limited and lifetime warranties on just about every type of shingle.

How many bundles of shingles do I need for 2000 square feet?

60 bundles
 
The number of bundles or squares you need will depend on the surface area of your roof, and its pitch or slope. For example, a 2,000 square foot roof will require 20 squares or 60 bundles. A professional will likely purchase slightly more materials than necessary to ensure there is extra material if needed.
 

How much does it cost to replace a roof on a 2200 square foot house?

A new asphalt shingles roof for a typical 2,000 to 2,200 square foot single-family house can range in price from $9,500 to $16,500 fully installed, including tear off and disposal of the old roof (up to two layers).