Estimate Roof Size

How to Calculate Roof Area

To calculate your roof area, simply multiply your roof length by your roof slope height, and multiply this by two. This should give you the total area of your roof, not accounting for a chimney or other sections of your roof not covered by tiles

Things You Will Need

  • Square footage of your house

  • Pitch of your roof

  • Calculator

  • Paper and Pen

Tip

This calculation will give a solid estimate for a single slope roof and a simple gable roof with a single pitch. For more complex roof lines with multiple pitch angles, it’s a little more complicated but the same steps can be followed; just break down the roof into separate sections with a different square footage for each different pitch angle.

Step 1: Sketch Roof Outline

Sketch the roof outline using ground measurements as shown in Figure 1 below. Knowing the longest dimension first will help you to scale your drawing appropriately.

Step 2: Fill in Roof Details

Measure and sketch out dormers, hips, valleys, diagonal distances and protrusions or overhangs. Chimneys, vents, skylights and pipe sizes will need to be measured to calculate trims and flashings needed for the job.

Pro Tip: You may need binoculars to count units of existing roof materials in unreachable areas. If different pitches exist on adjacent sides of a valley or hip, it’s length can be determined by treating the hip or valley as the diagonal (hypotenuse) of a right triangle on the roof pane next to it.

Roof Outline Plan Drawing

Figure 1. Sketching Your Roof Plan

Step 3: Determine Roof Pitch

Pitch refers to the angle of the roof, or how steep it is. Measured by inches of rise (vertical measure) over 12 inches of run (horizontal measure) In the gable diagram in figure 2. (below) there are 4 units of rise and 6 units of run. This can be converted to units of rise over 12 by understanding that cross products in step 2 must be equal. There Therefore 4 x 12 must equal 6 x X. Step 3 shows that X must equal 48 divided by 6. Therefore X equals 8 and the pitch is 8/12.

Formula for Calculating Roof Pitch

Figure 2. Calculating Roof Pitch

A Note About Pythagorean Theorem (Yes, You Need It in Real Life)

If you know the measurement of two sides of a right triangle, but not the third side, then the Pythagorean Theorem from 8th Grade geometry is your best friend. In Figure 2 above, rise squared (multiplied by itself) plus run squared equals the diagonal squared. In the diagram,  a+ b2 = c2. If the rise is 42 + 62 = c2, then 16 + 36 = c2 – So c = the square root of 52. Pythagorean Theorem tells us that the gable (diagonal) length is 7.21’ or about 7’ 3”.

Roof Pitches in Degrees
Use Our Roofing Calculator

Step 4: Calculate The Simple Roof Areas

On a simple hip or gable roof, multiplying the eave to ridge length by eave length will give the area to be multiplied by pitch factor. Ridge vent openings are best finished with coil rather than partial shingle. Using flat coil stock allows the ridge caps to lay flat and can also be formed with an extra water stop at the ridge opening.

Area for the roof in Figure 3 is 1784 ftThe blue dash line divides the roof into 2 rectangles. There is a small area calculated as 8/12 that is actually 4/12. On a small area such as this, it is better to err on the side of the higher pitch since it should not significantly affect the total.

Pro Tip: Pythagorean Theorem can be used to calculate the length of the valleys. A general rule of thumb is to add at least 12” lineal inches of valley material to be safe.

Plan for Calculating Simple Roof Areas

Figure 3. Calculating Simple Roof Areas

Step 5: Calculate The Complex Roof Areas

Most roofs in Canada would be considered on the complex side. Multiple adjacent pitches, dormers, and turrets are common. Keep in mind that an experienced metal roofing contractor will need to factor in extended labour time for areas of your roof that will require precision metalworking skills.

Start by finding the “footprint” area and multiply by the correct slope factor determined by pitch (see Pitch Factor Chart bottom of page). In Figure 4 below, the dashed blue lines give a simplified view of the “footprint”. Multiply L x W to calculate the area for each rectangular section. Note the area of 77ftthat needs to be subtracted for the recessed area.

Once the “footprint” including overhang areas have been determined for each area, find the appropriate slope or pitch factor in the chart below. For example, a roof area with an 8/12 pitch has a slope factor of 1.202 so 2053ftx 1.202 = 2468fttotal roof area.

A Note about complex roofs: Complex roofs need more accessories and trims than“easy” roofs – resulting in a slightly higher total cost/square foot.

How to Calculate Area for Complex Roof

Figure 4. Calculating Complex Roof Area

Step 6: Measuring or Calculating Gable and Hip Lengths

 The slope factor is also used to determine gable lengths when the run length is known. For example, in Figure 4 the bottom left gable measures 16’ across from eave to eave and therefore has a run of 8’. When this is multiplied by 1.202 the gable distance is 9’8” (9.62’ rounded up to nearest inch). Note that this run can also be multiplied by the hip/valley factor of 1.563 to get a valley length of 12’6”.

Record all your calculations on your drawing as seen in Figure 5 below.

Completed Plan Drawing of Roof with Measurements

Figure 5. Completed Roof Plan Drawing

 

Leave A Comment

You must be logged in to post a comment