Unlimited roof measuring app

Measuring Your Roof with Google Earth: A Step-by-Step Guide

How to Accurately Estimate Roof Size for Roofing Projects


Measuring your roof’s square photos is vital for obtaining specific Roofing fees and ensuring you purchase the appropriate materials. Here’s a step-by-step guide to measuring your roof and using Google Earth and other gear.


Roofing Quote Footage vs. Home Square Footage


Roofing Quote Footage: This is the entire region that needs to be included with Roofing substances, all roof surfaces, and capabilities like dormers or skylights.


Home Square Footage : refers to the total living area inside your home, not the Roofing area.


Measuring the Roof’s Pitch

The pitch or slope of your roof affects the amount of fabric you wish to use. 

Here’s a way to measure it:

Tools Required: Level, tape degree, pencil.


Method:

  • Position the Level: Place the extent horizontally on a roof rafter.

  • Mark 12 Inches: On the extent, mark off 12 inches.

  • Measure Vertically: Measure vertically from the 12-inch mark on the level up to the bottom of the rafter. This vertical dimension is the rise.

  • Calculate Pitch: The rise over the run (12 inches) expresses the roof pitch. For instance, a four-inch upward thrust over 12 inches is a 4/12 pitch.





Considerations for Different Roof Pitches

Roofs regularly have various pitches, particularly around features like porches or dormer windows.

  • Measure and notice each specific pitch to ensure accurate surface location calculations.

  • Using Google Earth for Roof Measurement


Google Earth can help estimate roof regions. 

Here’s how:

Steps:

  • Open Google Earth: Navigate to your own home.

  • Zoom In: Get a clear view of your roof.

  • Outline the Roof: Use the polygon tool to define the roof’s perimeter at factors in which the elevation is regular.

  • Avoid Peaks: Do now not outline along the peak of the roof, as angled satellite snapshots can distort measurements.


Precautions:

  • Image Angle: Aerial Roof Measurements may be angled, introducing errors. Aim for overhead perspectives when possible.

  • Complex Roofs: For roofs with multiple degrees or capabilities, degree each phase one by one.


Limitations of Google Earth

  • Accuracy: Google Earth provides a reasonable rough estimate but is not 100% accurate. Use it as a starting point, not the sole method for critical decisions.


  • Verification: Always verify measurements with manual techniques or expert equipment for unique estimates.


Final Steps

  • Combine Measurements: Integrate all the exceptional sections measured, accounting for pitch versions.


  • Calculate Total Area: Convert all measurements into rectangular pictures. Remember to add more for waste and overlap, generally around 10%.



Looking For a Roof Measurement Report?

Please Fill Out The Form Below -

Roofing reports

Roof Area Calculator | Google Maps

Tips:
  1. On your computer, open Google Earth.
  2. Search for a place, or select a location on the globe.
  3. On the left, click Measure. . …
  4. Click the map to set measurement points.
  5. To remove a point, on the right, click Undo .
  6. To complete your line measurement, double-click on your last point, or click Done .
A roofing square is an area of roof that measures 10 by 10 feet to make up a total of 100 square ft. This critical unit of measurement helps your contractor determine how much material they’ll need to order for your roofing project, from underlayment to bundles of roof shingles.
For a 1500 square foot house, you will need approximately 19 squares or 57 bundles or 1653 pieces of 3-tab standard-sized shingles (12 inch by 36 inch) when overhangs is 1 feet and roof slope is 4/12.
 To calculate this is simple: a roofing square is 100 square feet, which means that 20 roofing squares will accommodate a 2000 square feet roof. To obtain 20, you need to divide the total square feet by the size of one roofing square- 100 square feet.
That makes a total of 32 squares of roof for an “1800 square foot” house. 4) Roofers calculate roof area in “squares,” with a square being 100 square feet of roof area.

Looking For a Roof Measurement Report?

Please Fill Out The Form Below -

How to measure a roof and calculate square feet.

How do I Measure a flat roof?

Just measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane. Simply add the square footage of each of the planes together to derive the total square footage of your roof.

How to calculate a flat roof area in square metres. Measure the length and width of the structure from the outside for accuracy. Multiply the two figures to calculate the square meterage of the flat roof. E.G. 4 metres (length) multiplied by 3 metres (width) = 12 square metres in total.
Two feet is the general maximum length for a typical roof overhang. This will protect a roof from most types of damage. Roof overhangs can extend farther than 2 feet, but beyond this length, they begin to lose structural integrity and require external support.
A flat roof is generally any roof with a pitch of 1-10 degrees. That means flat roofs aren’t actually flat. It may look horizontal but often has a minimum slope of 1/4 inch per foot. This allows water to run off the roof to prevent damage.
Roof cost by material type. The average cost for a new asphalt roof in 2021 was about $28,256. Inflation was up 8.5% on average for the last 12 months (ending in March 2022). With this in mind, you can estimate that the average price for an asphalt roof will be about $30,700 in 2022.
Asphalt shingles are most often allowed in up to two layers, but no more. For flat roofs, materials such as EPDM and TPO are usually approved for use up to two layers.
The smallest pitch of a roof is 1/4:12, which translates to 1/4 inch rise to 12 inches of run. Such a small pitch can only work with built-up roofing or specialized synthetic roofing. Covered porches that are near trees or in areas with heavy rains should not be covered with a low-slope roof.
If your roof was properly installed, your attic is adequately ventilated, and your roof is maintained, it will get as close as possible to the maximum lifespan. This means you shouldn’t need a replacement for around 20 years or even up to around 50 years (or longer), depending on what kind of roofing material you have.

Looking For a Roof Measurement Report?

Please Fill Out The Form Below -

roof quotes online

Estimate Roof Square Footage Google Maps

Tips:
  1. On your computer, open Google Earth.
  2. Search for a place, or select a location on the globe.
  3. On the left, click Measure. . …
  4. Click the map to set measurement points.
  5. To remove a point, on the right, click Undo .
  6. To complete your line measurement, double-click on your last point, or click Done.
Right-click on the map at your starting point and choose the Measure distance option. Add points around the location’s boundary. Once you close the shape by clicking on the starting point, the Google Maps area calculator will automatically process the area of your shape.
Comparisons are made at sites in various states including rural and urban locations. The comparisons show that Google Earth images yield reasonably accurate measurements (RMSE 0.569 feet) over the scale of typical accident reconstruction distances.
First, measure the length and width of each surface on the roof, then multiply these values to get the square footage of that surface. Make sure to document the number of chimneys, skylights or other obstructions and include dormers in your measurements.
There are 12 roofing squares in 1200 square feet. The surface of roofs is basically measured in squares. One square is equal to 100 square feet of the roof. To calculate the number of squares of the roof, divide the total square feet by 100.
For a 1500 square foot house, you will need approximately 19 squares or 57 bundles or 1653 pieces of 3-tab standard-sized shingles (12 inch by 36 inch) when overhangs is 1 feet and roof slope is 4/12.
Once you’ve determined the square footage you need to cover, you can figure out the number of bundles you need by dividing the total square footage by 33. Example: if you have 2,000 square feet of roof to cover, that means you’d need about 60 bundles (2,000 divided by 33 is about 60).
The average cost for a square of roof shingles, which is 100 square feet, ranges from $170 to $400, depending on materials used. On the low end, asphalt shingles cost an average of about $150 per square, while high-end slate shingles average around $1,200 per square.
 
roof size calculator by address

Roof Measurement Report And Prices

Skyroofmeasure is the app for roofing contractors that provides fast and accurate roofing measurements, compelling reports and documents, and professional estimates designed to offer your customers options. Skyroofmeasure is the most robust roofing-specific software on the market.

Estimate Roof Size

BENEFITS:

  • Faster Bids: The Skyroofmeasure Reports enable roofers to compile fast, competitive bids. Delivered in just one hour, the report lists the number of squares and predominant pitch for a residential roof. When contractors upgrade to an Skyroofmeasure Report, they can deduct the cost of the  Report from the total price.
  • Greater Profitability: With an Skyroofmeasure Report, roofers receive the highly accurate roof measurements and diagrams they need to complete the job. Those precise details result in more efficient material orders and production plans, leading to less waste and increased profits.
  • Superior Accuracy: Before using Skyroofmeasure Reports, one group of contractors required material redeliveries 46% of the time and pickups 37% of the time. After switching to Skyroofmeasure Reports, only two of their jobs needed redeliveries, and the number of pickups fell to zero.
  • Professional Estimates: The Skyroofmeasure reports are delivered as a professional document with a customizable cover page included at no additional cost to the contractor. The property owner report offers a professional presentation utilizing  aerial imagery and the Skyroofmeasure 3D model. The ability to leave impressive aerial views with customers along with rapid estimates brands the company as forward thinking and reliable.
  • Negotiate and track labor charges: No haggling over steep charges or other crew payment issues when using Skyroofmeasure reports. Accurate pitch, area and line measurements make tracking labor easy and collaborative. Instead of square measurement disagreements, all parties can use the measurements for rapid and profitable labor and production.
  • Increase the number of sales calls made in a day: Contractors receive the measurements and information needed to prepare proposals ahead of time. Spend time selling, not measuring and estimating. The time saved means more calls can be made in a day resulting in more closed sales.
To determine if a roof is square, measure from the eaves to the ridge at several points along the roof to see how parallel they run. Do the same from one gable end to the other to determine parallel and also measure the roof diagonally.
 
How many roofing squares is 1600 square feet? So a roof that has 1600 square feet of area has 16 squares. Remember that unless the roof is flat, the square footage of the building is different than the square footage of the roof.

Asphalt three-tab shingles cost around $1 to $2 per square foot.

Price of Roofing Shingles Per Square Foot.

Roof AreaCost of Shingles
Roof AreaCost of Shingles
750 square feet$700 – $800
1,000 square feet$910 – $1,100
1,500 square feet$1,400 – $1,600
roof size calculator by address

Estimate the cost of a new roof online

Roof replacement cost for different roofing materials

Roofing materialAverage cost per square footAverage total replacement cost*
Asphalt shingles$3.40 – $5.95$5,840 – $10,100
Metal roofing$6.00 – $24.50$10,245 – $41,640
Tile roofing$6.30 – $12.30$10,665 – $20,900
Wooden shakes / shingles$6.00 – $9.15$10,230 – $15,500

The average cost to replace a roof can vary quite a bit. The typical range for roof replacement costs is between $5,100 and $10,000, but roof replacement can be as low as $1,200 or as high as $30,000. Many roofing companies will charge between $3.50 and $5.00 per square foot.

This results in a wide range of costs associated with replacing your roof . The state average cost to replace a roof is $6,000 to $20,000, with most homeowners paying around $12,000 for a 2,000 sq. ft. roof replacement using hail-resistant architectural shingles.
 
Estimate the cost of a new roof online
Tile and Asphalt are the most used materials for roofing, and they’re manufactured with the usage of concrete, clay or oil. The rise of oil prices can directly impacted asphalt shingles to become more costly. Furthermore, the cost of disposing old and damaged materials has also increased in the recent years.
In 2022, roofing material prices increased by about 6%-8%, and may continue to rise by 10%-12% within the next year. This includes the prices for shingles, underlayment, decking, and other essential materials for a high-quality roof.
That’s for good reason. Asphalt is the cheapest of all roofing materials in the market and will last you between 15 to 30 years. This is the best option for homeowners facing budgetary constraints. It is also widely available and comes in a variety of colors.
Roofing material that lasts the longest are concrete, clay or slate tiles. These materials significantly outperform other natural products like wood shakes or any manufactured roofing materials including asphalt shingles and metal roofing. Although these materials have a good lifespan, they are not as durable.
Metal roofing is by far one of the best choices you can make for your roof in general. They’re the most energy-efficient roof for residential installations, can last more than 50 years, and require very little maintenance. Metal roofs are very reflective, which is why they get so hot to the touch.

Sky Roof Measure provides industry leading takeoff and estimating reports for professional construction contractors. Please Email : info@skyroofmeasure.com

Looking for a Roof Measurement Report?

Please fill out the form below -

Screen Shot 2021-08-12 at 4.51.11 PM

How many squares does it take to roof a 2000 square foot home?

How many shingles do I need to protect my roof?

The surface area of your roof will affect the number of bundles or squares you need. A 2,000 square foot roof requires 20 squares or 60 bundles.

A roofing square is equal to 100 square feet of the roof. To determine the number of squares on the gable roof example in this post, divide its total of 2400 square feet by 100 (2400 ÷ 100 = 24). This means you would need 24 squares of shingles to cover that roof.
One square is equal to 100 square feet. Examples where the unit is used are roofing shingles, metal roofing, vinyl siding, and fibercement siding products. Some home builders use squares as a unit in floor plans to customers.
A square of shingles is the quantity needed to cover 100 sq. ft. of roof. Shingles are packaged in paper- or plastic-wrapped bundles designed to be light enough for a person to carry, so heavier shingles require more bundles per square.
aerial roof measurement
Asphalt three-tab shingles cost around $1 to $2 per square foot.

Price of Roofing Shingles Per Square Foot.
Roof AreaCost of Shingles
750 square feet$700 – $800
1,000 square feet$910 – $1,100
1,500 square feet$1,400 – $1,600
The size of a three-bedroom home can vary depending on the size of additional rooms, with an average of 1,200-1,300 square feet. This is equivalent to 110-120 square metres.
There are 12 roofing squares in 1200 square feet. The surface of roofs is basically measured in squares. One square is equal to 100 square feet of the roof. To calculate the number of squares of the roof, divide the total square feet by 100.
With that said, on average, most roofing companies will charge somewhere between $3.50 and $5.50 per square foot, or $350 to $550 per square (100 square feet) to install or replace an asphalt shingle roof.
 
By saying this, you might already realize that the difference between a 30-year shingle and a 50-year one is how long the product is guaranteed to last. In other words, 30-year architectural shingles are covered by the manufacturer from any unforeseen defects that could occur once the shingles are installed.
One Click Roofing Estimates

Measure Roof From Satellite Free

The good news is there is a way to measure your roof in a safe and accurate way, all from the comfort of your home: use Google Earth. With just a few clicks, you can search for any address, get a bird’s eye view of your roof, and get the roofing measurements that you need.
To do this, measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane. Finally, calculate your roof’s total square footage by simply adding the square footage of each of the planes together.

Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email : info@skyroofmeasure.com

How many shingles do i need for a 12×12 shed:- for a 12×12 shed roof, you will need approximately 3 squares or 9 bundles or 261 pieces of three tab strip standard-sized shingles (12 inch by 36 inch) when overhangs is 1 feet and roof slope is 6/12.
How many bundles of shingles do i need for 1200 square feet:- for 1200 square feet or 12 squares roof, you will need approximately 36 bundles of standard size 3-tab shingles (12×3 = 36 bundles). Thus, for a 1200 square foot gable roof, you would need 36 bundles of shingles plus 10% of ridge, starter and wastages.

Cost of Shingles

Prices are based on a cost of around $30 to $35 per bundle of asphalt three-tab shingles or about $90 to $100 per square

By saying this, you might already realize that the difference between a 30-year shingle and a 50-year one is how long the product is guaranteed to last. In other words, 30-year architectural shingles are covered by the manufacturer from any unforeseen defects that could occur once the shingles are installed.

Looking for a Roof Measurement Report?

Please fill out the form below -

Roof Area Calculation

How to Calculate Roof Areas?

Multiply your house length by your house width to get the area. (For example, 40 feet x 30 feet = 1,200 square feet.) Next, multiply the area by your roof’s pitch. (1,200 x 1.05 = 1,260 square feet.)
sky roof

Finding the Size of the Roof in Squares


A square simply refers to a 10′ x 10′ square of roofing. This is simply 100 square feet of roof. To find the squares, divide the overall roof area by 100 and then round up. For instance, if the roof is 1550 square feet, then it is 16 squares.

Since there are twenty six shingles in a bundle of twenty year shingles (which is fine for starters and edges), divide the result by twenty six. For the number of ridge caps, multiply the length of the hip or ridge by twelve and divide it by five. This house is 1000 square feet. It requires 18 squares of shingles.

How many squares is 900 square feet?

Conversions Table
10 Square Feet to Roofing Squares = 0.1800 Square Feet to Roofing Squares = 8
20 Square Feet to Roofing Squares = 0.2900 Square Feet to Roofing Squares = 9
30 Square Feet to Roofing Squares = 0.31,000 Square Feet to Roofing Squares = 10
 

Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email : info@skyroofmeasure.com

Can I get roof measurements from Google Maps? How do you measure a roof without measuring it?
A 200 square foot space is about the size of a one-car garage. In other words, the average car could fit into 200 square foot place with a small amount of wiggle room. Imagine a space smaller than a bedroom for 100 square feet.
roof quotes online

Roofr measurements

  1. On your computer, open Google Earth.
  2. Search for a place, or select a location on the globe.
  3. On the left, click Measure. . …
  4. Click the map to set measurement points.
  5. To remove a point, on the right, click Undo .
  6. To complete your line measurement, double-click on your last point, or click Done .
aerial roof measurement
To do this, measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane. Finally, calculate your roof’s total square footage by simply adding the square footage of each of the planes together.
For example, if you want to figure out the actual length of a common rafter with a plan length of 10′ for a “10 in 12” roof you would simply multiply the plant length by the “10 in 12” factor for common rafters. Therefore, the actual length would be 10′ x 1.302 = 13.02′.

Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email : info@skyroofmeasure.com

Aerial measurement
A roofing square is an area of roof that measures 10 by 10 feet to make up a total of 100 square ft. This critical unit of measurement helps your contractor determine how much material they’ll need to order for your roofing project, from underlayment to bundles of roof shingles.
Since there are twenty six shingles in a bundle of twenty year shingles (which is fine for starters and edges), divide the result by twenty six. For the number of ridge caps, multiply the length of the hip or ridge by twelve and divide it by five. This house is 1000 square feet. It requires 18 squares of shingles.
How Many Bundles of Shingles Will You Need. The average bundle of shingles covers 33.3 ft2, so three bundles of shingles are needed per square.
roofer

Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email : info@skyroofmeasure.com

Price of Roofing Shingles Per Square Foot

Roof AreaCost of Shingles
1,000 square feet$910 – $1,100
1,500 square feet$1,400 – $1,600
1,750 square feet$1,600 – $1,850
2,000 square feet$1,810 – $2,110
$2,400 – $6,000
 
They generally range between $55 on the low end and $600 on the high end, with an average of $100 to $250 per square of architectural shingles.

Roof Shingles Cost per Square.
Number of SquaresCost (Including labor)
12 squares$2,400 – $6,000
15 squares$3,000 – $7,500
17 squares$3,400 – $8,500
Roof Calculations of Slope, Rise, Run, Area

How Do You Calculate Rafter Length

How to calculate rafter length?

The formulas we use are the following:

  1. For calculations based on the roof rise:

rise² + run² = rafter length² ,

meaning that:  rafter length = √(rise² + run²).

aerial roof measurement
Pitch – Is the incline of the roof represented as the ratio of rise to the span (twice the run). For example, if the roof rises 4 feet and the span is 16 feet (twice the run), then the pitch is 4/16, or 1/4.
But they do tend to space rafters in one of several industry-standard increments, typically either 12, 16 or 24 inches apart. These spacing intervals are measured “on center,” meaning that the measurement is taken from the center of one rafter’s horizontal surface to the center of the next rafter.
Maximum allowable span for a 2×6 rafter:- the maximum allowable span for 2×6 rafter is 16 feet 5 inches when spaced 12 inches apart from centre, 14 feet 8 inches at 16″ OC & 12 feet 8 inches at 24″ OC with best quality No.
 

* Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email Us : info@skyroofmeasure.com

Estimate Roof Size
The length of the rafter is given from the long point of the ridge cut at the top down along the top edge the board to the same plumb cut on the rafter’s notch. The next result is the run. This is the horizontal measurement from the outside of the wall to the inside of the ridge.
Rafter span: this is the distance between the supporting wall and the centre of the roof measured horizontally. The span is NOT the distance between the supporting wall and the peak of the roof measured along the diagonal. Rafter: This is the lumber that runs from the centre (peak) to the supporting wall.
2-grade 2×6 joists can span up to 10 feet 9 inches from beam to beam when spaced the standard 16 inches apart with a maximum live load of 30 inches per square foot. In comparison, No. -1 grade lumber can span slightly further to 10 feet 11 inches under the same parameters.
 
In general, a 2×8 will span 1.5 x 8, so 12-feet. Based on all factors though, a 2×8 joist span is 7′-1” to 16′-6”, and a rafter 6′-7” and 23′-9”. In this guide, we’ll explain what span means in terms of construction, factors that impact the span, and how much weight a 2×8 can support.
 
roof quotes online

* Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email Us : info@skyroofmeasure.com

roofer

How To Calculate Roofing Square feet

A roofing square is a 10×10 area that’s equal to 100 square feet of roof surface.
A square simply refers to a 10′ x 10′ square of roofing. This is simply 100 square feet of roof. To find the squares, divide the overall roof area by 100 and then round up. For instance, if the roof is 1550 square feet, then it is 16 squares.
So a roof that has 1600 square feet of area has 16 squares. Remember that unless the roof is flat, the square footage of the building is different than the square footage of the roof.

How to measure your roof’s square footage 

The square footage of your roof has a huge impact on the cost of your replacement. It affects a number of cost factors, including the amount of materials used, labor, and time. 

Be aware, the only way to get a 100 percent accurate measurement is to have a local roofing contractor come out to professionally measure your roof and give you a quoteHowever, I can give you the calculations to get a rough measurement of your home’s square footage.

Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email : info@skyroofmeasure.com

roof quotes online

Area of a rectangle or square:
A = L x W
Area = Length x Width
Example: 20 feet x 10 feet = 200 square feet

Area of a trapezoid:
A = [(B1 + B2) x H] / 2
Area = [(Top + Bottom) x Height] / 2
Example: [(5 feet + 10 feet) x 6 feet] / 2 = 45 square feet

Area of a triangle:
A = (B x H) / 2
Area = (Base x Height) / 2
Example: (5 feet x 4 feet) / 2 = 10 square feet

When you have finished calculating the area of each plane, use this information to find your roof’s total square footage. Add the area of each plane together, and the sum will be the total square footage of the roof.

The Drip Cap

  • Before you do any roofing work, you must calculate the roof’s square footage to determine how much material you need.
  • Calculate each plane separately.
  • For example, if a triangle-shaped roof plane measures 60 feet along the base and is 30 feet high, we have 60 x 30 = 1,800 feet, divided by 2 = 900 square feet for the triangle-shaped plane.
  • The square footage would be 40 x 40 = 1,600 square feet (the square) plus 20 x 40 = 800 / 2 = 400 square feet (the triangle).
Measure distances and areas in Google Earth

**  Sky Roof Measure provides industry leading takeoff and  Roof  estimating Reports for professional construction contractors. Please Email : info@skyroofmeasure.com

A roofing square is equal to 100 feet on your roof. If your roof measures at 1800 square feet, you would need 18 squares of shingles to cover your roof.
The three nutritionally complete meals (in one day), that is, breakfast, lunch, and dinner.
Square of 112: 1122 = 12544
1.What Is the Square Root of 112?
2.Is Square Root of 112 Rational or Irrational?
3.How to Find the Square Root of 112?
4.FAQs on Square Root of 112
 

Looking For a Roof Estimating Report?

Please fill out the form below -

SkyRoof Measuring

Roof Measurements

What is the standard unit for roofing measurement?

A roofing square is a unit of measurement for calculating the size of a roof and is equivalent to 100 square feet. The larger unit is useful for calculating the amount of material needed for a roof. It’s common to calculate the size of your roof in “squares”, and then order an additional 15% in backup materials.

How do you calculate the rise and run of a roof?

Calculate the roof rise using the figures for unit rise and total run. Multiply your figure for unit rise by your figure for total run to get the total rise. Using the example, it would be six inches times 13 feet. The total roof rise in the example equals 78 inches.

How do I calculate a rise?

Subtract the difference in elevation between two points on a hill to calculate the rise. The elevation could be determined by an altimeter or you could use a topographic map. As an example, you might read 900 feet at the top of a hill and 500 feet at the bottom, so subtract 500 from 900 to get a rise of 400 feet.
 

What are the 4 types of slopes?

Slopes come in 4 different types: negative, positive, zero, and undefined. as x increases. The slope of a line can also be interpreted as the “average rate of change”.

How to measure your roof area from the ground

A more accurate way to calculate the area of the roof than using Google Earth is to get outside to estimate the roof pitch and the base area of the property. Using these two figures, we can get a good idea of the shingle roof’s square footage and estimate your asphalt shingles’ needs and costs. This DIY technique can be helpful, especially if you are not comfortable getting on your roof, or if you have limited access to it.

Ground measures only work well for a gabled roof, since there are usually just two main rectangular pitches to calculate area for. For more complex roof shapes, like hip roofs, you’ll need to work with a roofer or measure from on top of the roof itself to calculate its total area.

Roof Measurement Report :

The Roof Measurement Report provides a detailed analysis of your roof layout and all the critical dimensions. Our full color report provides the detailed lengths, pitch and areas of every surface plane and edge. This report saves your time and enables accurate roof estimates for a roof repair or replacement. This is a professional grade report used for use by licensed roofing contractors or insurance companies. You will receive the report in .PDF format by email within 1-3 days. Follow us!

REPORT INCLUDES THE FOLLOWING:

  • Images: 1 Orthogonal (overhead), 4 Oblique (birds eye), and 1 Street View (where available), all in full color.
  • Roof Measurements and Areas: includes Eaves, Rakes, Ridges, Hips and Valleys, and edges are all separately measured and identified.
  • CAD style drawings with colored lines identifying every type of roof edge and area for each plane/section.
How to measure a roof and calculate square feet.

Roof and Wall Measurement Reports

The Survey will report on items listed in a Homebuyers Survey in relation to the roof including the condition of the tile or slate covering, the chimneys, fascia boards, gutters and any roof windows.

How do you perform a roof inspection?

The 10 steps to performing a roof inspection are: 1: Check the roof covering 2: Check the fasteners 3: Check the deck sheathing 4: Check the slope and underlayment 5: Check the ice barrier 6: Check the drip edge 7: Check for an offset pattern 8: Check the roof valley flashing 9: Check the nail penetration into the deck.

What is included in a roof inspection?

While an interior roof inspection includes checking the attic for proper insulation, ventilation, as well as moisture and mold, an exterior inspection includes climbing up on the roof and checking for leaks and proper flashing, as well as the condition of your shingles and chimney.
 
Here’s a roofing inspection checklist:
  1. Cracked caulk or rust spots on flashing.
  2. Shingles that are buckling, curling, or blistering.
  3. Missing or broken shingles.
  4. Cracked and worn rubber boots around vent pipes.
  5. Missing or damaged chimney cap. …
  6. Masses of moss and lichen, which could signal the roof is decaying underneath.

What will fail a roof inspection?

Common roof problems found in home inspections include a failing structure (sagging), poor installation or workmanship, leaks, missing/damaged shingles, improperly installed flashings, and clogged gutters and downspouts.

Should I get my roof inspected?

A good rule of thumb is to get a professional to have a look at it regularly. We recommend every 3 years for a tile roof and every 5 years for a metal roof. … Even if your roof has no visible issues, it is a good idea to have it inspected regularly for any hidden problems.
 

How often does a house need a new roof?

Composition shingles that make up a roof will last about 12-20 years, while asphalt, one of the most popular roofing materials, will last a little longer, about 15-30 years. Surprisingly, wood shingles last about 20-25 years, and finally, metal roofs hang around for 50-75 years.

How often do you need to do roof maintenance?

every 3-5 years
 
General guidelines suggest that your roof needs an inspection every 3-5 years depending on the type of roof you have. To keep small problems at bay, our experts recommend having your roof inspected more often than that. If it’s been longer than that, it’s time to give us a call so we can come look at it.
Satellite Roof Measurement

How do you measure a roof without measuring it?

To find your roof’s total square footage:
  1. Measure the length and width of each plane on the roof (including dormers) then multiply length times width.
  2. Add the square footage of each of the planes together.

How do you measure a roof with a tape measure?

Ask the assistant to hold one end of the tape in line with the outer edge of the roof at one end, and measure to the opposite, outer end of the roof. Multiply the angle measurement for the pitch of the roof by the length of the roof to determine the square-foot area of one side of the gable.

How do you calculate the area of a roof without pitch?

Figure the area of small sections, such as crickets at the back of a chimney or short hips, by multiplying the length times the width at the widest point instead of using exact measurements.
aerial roof measurement

How do you calculate the area of a sloped roof?

Determine the area protected by the sloping roof by multiplying the length of the roof by the width. The result is the area covered by the sloping roof. For example, a single sloping roof covering a house 30 feet long and 20 feet wide covers an area of 600 square feet — 30 x 20 = 600.

Roofing Quote Footage is Not the Same as Home Square Footage

Depending on where the information is coming from is going to determine the basis on which the estimated roof footage is calculated. The roof square footage is what we (roofing contractor) need to calculate a budget quote to do the job.

How big is a roof on a 2000 sq ft house?

Approximately 3,000 square feet
 
Square Footage of Your Roof:

So a trick to estimate your roof size is to multiply the square footage of your house by 1.5 (ex: A 2,000 square foot house will have a roof that is approximately 3,000 square feet).
 

How much does it cost to replace a roof on a 2200 square foot house?

A new asphalt shingles roof for a typical 2,000 to 2,200 square foot single-family house can range in price from $9,500 to $16,500 fully installed, including tear off and disposal of the old roof (up to two layers).
 

Accurate roof measurement

Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area. Note any skylights, chimneys or other parts of the roof that would not require materials. You can subtract those measurements from your total area.
Can I get roof measurements from Google Maps? How do you measure a roof without measuring it?

Simple Residential Roof Report

How to Write a Roof Inspection Report [With Templates]
  1. Communicate details in a way the homeowner can understand. …
  2. Create a separate roofing estimate. …
  3. Use the report as a marketing opportunity. …
  4. Use resources to build roof inspection reports. …
  5. Keep it professional.

What is included in a roof inspection?

A roof inspection examines wear and tear, estimates the lifespan of a roof, and recommends repairs if necessary. The inspector should be able to identify roof features that are unsafe or in poor condition. Please Click here to know more about us!

What is a roof report?

A Roof Report is a written report, that is issued by an individual or by a company that is a licensed roofing contractor, after a Roof Inspection has been completed on the roof of a home.

What is a roof condition report?

The purpose of the roof condition report is to guide long-range planning. The roof condition report should explain the investigation methodology employed, the findings, the prioritized conceptual recommendations, and the probable cost of recommended repairs or replacements

What does a roof adjuster do?

The insurance company sends an adjuster to your house to inspect your roof insurance claim, assess the damage, and determine what is and is not covered for your roof claim.

How do you assess a roof?

Exterior Inspection
  1. Step back far enough from the house that you can see the entire roof, and look for sagging or uneven slopes. …
  2. Look through binoculars to assess shingle condition. …
  3. Walk around the entire house. …
  4. Look at metal flashing around chimneys, vent pipes and sidewalls.

Roof Evaluation

The primary purpose of a roof assessment is to evaluate and identify the level of wear and tear of your roof. In doing so, you will learn whether repairs are needed to your roof. To determine if your roof has any damage or wear and tear, a roofer is looking for certain signals of indication on the roof.

How much should a new roof cost?

How much does a new roof cost? Many factors will affect the cost of roof replacement, but some general costs for a three-bedroom house may be: $6,000 to $10,000 to replace metal roofing with Colorbond$15,000 to $20,000 to replace an asbestos roof with Colorbond.
 

How long is a roof good for?

Slate, copper and tile roofs can last more than 50 years. Homeowners with wood shake roofs should expect them to last about 30 years, while fiber cement shingles last about 25 years and asphalt shingle/composition roofs last about 20 years, the NAHB found.
aerial roof measurement

A Quick Guide to Roof Measurements

Determine the square footage of one floor of your home. (For example, if you have a two-story home that’s 2,600 square feet, one floor would be 1,300 square feet.) Multiply this number by your most recent result to get the estimated square footage of your roof. (1,300 x 1.05 = 1,365 square feet.)

How do I measure my roof for metal roofing?

Determine the length of the metal panels needed for one side of your roof by measuring from the fascia board (the board attached to your roof joists) to the ridge (the peak) of the roof. For example, your roof could measure 12 feet to its peak. This number will tell you the total length of metal panels needed. Follow Us !
 
Average Cost to Replace a Roof by House Size
House (& Roof**) by Square FootRe-Roofing Cost*
1,000 (1,054)$4,000 – $5,500
1,100 (1,160)$4,200 – $6,000
1,200 (1,265)$4,500 – $6,500
1,500 (1,581)$5,500 – $8,000

How many square feet is a typical roof?

The average residential roof size in the US is about 1,700 square feet or 17 squares, although there are many larger homes with roofs that can be well over 2,000 sq. ft. or 20 squares. In fact, larger residential properties with garages can easily exceed 3,000 sq.
 

square feet

The roofs are measured in squares. 100 square feet is equivalent to a square in roofing terms. The roof of the average home is 3000 square feet. The measurement of your roof is easy to figure out.
 

What is the standard width of metal roofing?

The two most common widths are 26 and 36 inches. Other standard widths include 24 and 39 inches. When calculating coverage using the width and length of corrugated roofing, keep in mind that each piece will need to overlap by several inches.

What type of roofing is best?

Best Roofing Materials for Longevity and Durability
  • Asphalt Roll.
  • Built-Up Roofing (BUR)
  • Composite Asphalt Shingle.
  • Wood Shingle.
  • Wood Shake Shingle.
  • Standing-Seam Metal.
  • Clay or Cement.
  • Slate.

What color roof lasts the longest?

Both light-colored and dark-colored shingles can last longer if given the necessary maintenance. The only thing tested and proven about light-colored shingles is that they help us keep the indoor temperature cooler in the hot summer season.

Which roof lasts the longest?

Roofing material that lasts the longest are concrete, clay or slate tiles. These materials significantly outperform other natural products like wood shakes or any manufactured roofing materials including asphalt shingles and metal roofing. Although these materials have a good lifespan, they are not as durable.
roof

Roof Measurements from Satellite USA

How do you measure a roof on Google Earth?

  1. On your computer, open Google Earth.
  2. Search for a place, or select a location on the globe.
  3. On the left, click Measure. . …
  4. Click the map to set measurement points.
  5. To remove a point, on the right, click Undo .
  6. To complete your line measurement, double-click on your last point, or click Done .

Are satellite roofing estimates accurate?

Get Accurate Measurements AND Estimates in Minutes: Satellites are more accurate than the most experienced contractor’s hands. You’ll get EXACT measurements of your roof with no human error. … It’s 100% Safe: Did we mention no ladders, measuring tapes, heights, or hot sun? Yeah, this is way safer!

How do I get an accurate roof measurement?

Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area. Note any skylights, chimneys or other parts of the roof that would not require materials so you can subtract those measurements from your total area. Follow Us!!

How do you estimate roofing costs?

Measure the square metre area of the roof you want replaced. The range of prices to replace your roof is: $50 to $95 per square metre. So multiple this rate against the square metre of the roof you want replaced.

Which of the measurements is the most accurate?

The measurement 4.00 mm is most precise because it is measured with an instrument of minimum least count.

Can drones measure roofs?

Drones present a unique opportunity for getting a clear view of your rooftop and allowing you to get precise roof measurements. A variety of roof measuring applications and programs already take advantage of high-resolution drone imagery to get accurate roof measurements
Estimate Roof Size

Measure Roof From Satellite Free

Are satellite roofing estimates accurate?

Get Accurate Measurements AND Estimates in Minutes: Satellites are more accurate than the most experienced contractor’s hands. You’ll get EXACT measurements of your roof with no human error. We’ll even provide an estimate for costs based on the average roofing materials. Get to know more!
 

How to Calculate Total Square Footage of Your Roof

  1. Measure the length and width of each plane on the roof (including dormers) then multiply length times width.
  2. Add the square footage of each of the planes together.

How do I estimate the cost of a new roof?

The average cost to replace a roof can vary quite a bit. According to HomeAdvisor, the typical range for roof replacement costs is between $5,100 and $10,000, but roof replacement can be as low as $1,200 or as high as $30,000. Many roofing companies will charge between $3.50 and $5.00 per square foot.
 

Call Us for Roof Measurements : (315) 926-1777 

OR  Email us : info@skyroofmeasure.com

Can drones measure roofs?

Drones present a unique opportunity for getting a clear view of your rooftop and allowing you to get precise roof measurements. A variety of roof measuring applications and programs already take advantage of high-resolution drone imagery to get accurate roof measurements.
 

Can drones measure height?

While aerial photography is the most common use of a drone, many of the models available in the market are also capable of measuring height, the height of the drone above ground, or the altitude above the mean sea level.

How do you measure a roof with a tape measure?

With your measuring tape, measure vertically from the top point to the bottom point of your roof. (This is also called the rise.) Repeat this over 12 inches, then place the measurement over “12”. (For example: If your rise is 4 inches over 12 inches, then your slope measurement is 4/12.)
 

How many bundles of shingles do I need for 100 square feet?

Asphalt shingles are typically packaged with this in mind, but if a package of shingles covered an entire 100 square foot square, it would be too heavy to handle. So, most popular shingles are sold such that three bundles are needed to cover one square of roof area.
drone

Roof Report by Blueprints

Once the drawing was exposed to light, the exposed parts turned blue, while the drawing lines blocked the coated paper from exposure and remained white. … For decades, bluelines were the way to make copies of architectural drawings. To this day, they are often called blueprints.

The most important thing is to match the scale of the ruler used for measurement to the drawing.

  1. Unroll the blueprint onto a flat surface. …
  2. Find the scale of the drawing. …
  3. Choose a scaled ruler that accurately matches the scale of the drawing. …
  4. Lay the proper scale next to the item on the drawing and take the measurement.

4 Tips for Reading Blueprints

  1. Begin with the title block. The title block is the first piece of information you’ll see in construction site plans. …
  2. Study the plan legend. …
  3. Find the blueprint’s scale and orientation. …
  4. Look for notes from the architect.
What Are the Six Types of Construction Drawings?
  • Plans.
  • Interior and exterior elevations.
  • Building and wall sections.
  • Interior and exterior details.
  • Schedules and room finishes.
  • Framing and utility plans.

What type of construction drawing is a roof plan?

A roof plan will usually just be a 2-dimensional drawing that depicts your roof from a bird’s eye view. The plan is written to coincide with the scale of your home’s floor plan. It will often include notes that detail specifics about the pitch of the roof, as well as its ridges and slopes.

Do architects still use blueprints?

Blueprints are still being used to this day. However, they are no longer blue and aren’t called blueprints. They are now referred to as drawings or plans. … But due to modern printing methods, architects no longer need to put the drawings through the chemical process that makes them blue.
 

What is the importance of roof framing and roof plan?

 
May's ABI shows healthy demand for all types of construction - Construction  Specifier
 
One of the most important parts of building a sturdy roof is the initial roof framing plan. Roof framing simply describes how a group of rafters and beams are fitted or joined together in order to provide support for the roof covering.
 

The main sections of a blueprint are:

  • Title Sheets and Site Plans.
  • Floor Plans.
  • Elevations and Sections.
  • Details and Schedules.
  • Structural Drawings.
  • Mechanical, Electrical, and Plumbing (MEP) Drawings.
 
Roof Area Calculation

Sky Measure Roof

Accuracy Is The Key To Success. No Other Words Can Explain The Importance. Our Aerial Roof Measurement Reports Are Prepared By Trained CAD Technicians Followed By A 3 Step Verification Process By A Quality Assurance Professional, Certifying Absolute Data Accuracy On Every Report We Deliver.

Call us : (315) 926 1777

Email: info@skyroofmeasure.com

Created by roofing experts, for roofing experts, SkyRoofMeasure provides comprehensive and affordable roof measurement reports to save you time and money. Reports are based on high-quality, up-to-date aerial imagery and help contractors and insurers quickly and easily estimate roofing jobs.

What do you need to know about aerial roof measurement?

Precise measurements must be taken to ensure the success of the project. SkyRoofMeasure™ aerial roof measurement reports are now available directly from blueprints, taking aerial roof measurement an extra step further to ensure that all of the angles are covered.

HOW TO ESTIMATE THE SIZE OF YOUR ROOF

Step One: Sketch Out Your Roof on Grid Paper

By doing this, you will have a much easier time figuring out the roof pitch and the roof surface areas. The best way to go about this by getting the longest dimension of the roof. A good thing to remember is that one roof square is equal to 100 square feet. Count how many squares there are and take that number and convert it into the measurement units you want to use for your drawing.

Step Two: Fill in the Details of Your Roof

Take note of things like valleys, diagonal distances, protrusions, overhangs, dormers, and hips as these will need their own measurements. Chimneys, vents, skylights, trim, and even pipes all affect the surface area of the roof. You may need to use binoculars to count out the squares of shingles in places that are unreachable. Sketch these areas out onto your roof diagram before moving onto the next step.

Step Three: Determine Roof Pitch

There are three ways by which you can measure your roof’s pitch.

  • Grab a ladder and place a level a foot or so up on the roof and hold. Measure the 12-inch mark from the bottom of the level down onto the roof. If this distance measures at four then you have a 4 in 12, or if it measures at 8, you have an 8 in 12 pitch.
  • Grab a ladder and jump up at the end of your house where the gable is. Place the level on the gable trim, flat against the house. Measure from the 12-inch mark on the level up to the bottom edge of the gable’s trim. The distance you get is the roof’s rise.
  • If you have an attic, you can place the level against one of the rafters and mark where the 12-inch mark is on the bottom of the rafter. Measure from the end of the level up to the bottom edge, and this will give you the roof’s rise.

The most common roof is a 6 in 12, which is a 27-degree angle with anything above this being anywhere between 30 and 45 degrees. Anything below a 6 in 12 is anywhere from a 5 to 23-degree angle.

Step Four: Calculate the Area of Your Roof

There are a few ways you can go about this, but typically the easiest way is to calculate the simple areas of the roof and then calculate the more complex areas. You can do this by finding out the estimated amount of how many shingles you will need. Measure out the length and width of each plane on your roof, including things like hips, dormers, and adjacent pitches. Multiply the length by the width to get the square footage of each plane.

Step Five: Input Results into a Roofing Calculator

Once you have the roof size in square feet (or in length times width as feet), the roof pitch, and the material you want your shingle to be, you can use a roofing calculator to get the total square feet of the roof area, the number of squares it has, and what the range of the installation cost will be. The average 1,700 square foot roof will have a roof area of around 1,901 square feet with twenty squares, and an installation cost of anywhere between $7,224 to $14,300.

When Ordering a Roofing Report Is More Effective: Even an experienced roofer/drone operator will need to study any photos or footage of a property carefully in order to make a detailed estimate or contract. Drones may be effective tools, but they are essentially just eyes in the sky – you might still run the risk of the operator miscalculating or misjudging critical data that can impact your orders, scheduling, and bottom line.

Know Your Teams’ Skillsets and Tools: Using drones for your roofing or contracting business can be a huge asset when it comes to documentation and archives. However, it’s important that you don’t come to rely on the skillset and license of one or two people.

Make sure your drone operators are professional – you are trusting them with an expensive piece of company property. While accidents can always happen, you should make sure that the person operating the drone always has their certified FAA license on hand, and can report back immediately if something does happen to the drone.

Know when a drone is an asset, and when it’s more cost and time effective to order a report. This may be up to your rep’s discretion, or you may have a protocol in place. Either way, it’s important to remember that while the drone is a fantastic piece of technology, that doesn’t always mean it’s the ONLY technology at their disposal.

How are blueprints measured? Unroll the blueprint onto a flat surface. ... Find the scale of the drawing. ... Choose a scaled ruler that accurately matches the scale of the drawing. ... Lay the proper scale next to the item on the drawing and take the measurement.

Roof Measurement

How To Measure A Roof
  • Step 1: How to Calculate Your Roof Square Footage. First, measure the length and width of each surface on the roof, then multiply these values to get the square footage of that surface. …
  • Step 2: How to Determine Your Roof Pitch. …
  • Step 3: Calculating Roof Squares.

Please Follow us for more in details ..

Call us : (315) 926 1777

Email: info@skyroofmeasure.com

Satellite Roof Measurements

In most areas of the United States, a satellite image provided by Sky Roof Measure of a home’s rooftop is perfectly suitable as your basis for a complete and accurate roof measurement.  has Sky Roof Measure  integrated this technology into a simple user design. Search by address in the Sky Roof Measure app; click to open the satellite view and zoom right in. Now, just trace the linear features of the roof, which instantly calculates precise measurements. Now you’re ready to see a detailed report with the press of a button. It’s all there, the total square footage, roof squares, waste factors, and professional roof diagrams. In no time, you’ll master this simple application with your tablet or smartphone. Get ready to work more efficiently and more profitably!

Drone Roof Measurements

The rising popularity of drones in the roofing industry is no accident. Professional contractors everywhere are seeing the advantages of merging technology with their toolbox; allowing increased safety, higher accuracy, less headaches, and the type of modern presentation clients now expect. Simply put, combining high-resolution drone imagery with a powerful roof measurement application  means more sales. The days of spending 30+ minutes on a roof to calculate measurements – only to lose the bid – are becoming a thing of the past.

Roofing Squares: A Way To Measure Your Roof

What Is A Roofing Square?

A roofing square is a measurement, but it has nothing to do with square feet, meters, yards, or miles. A roofing square is commonly used by roofing companies and is roughly equivalent to 100 square feet. This measurement does not change whether it is a square of shingles or a square of tarp. This is because roofing squares are used to make calculating the cost of materials and labor easier than if you had to use square feet or yards.

Who Uses Roofing Squares?

The roofing square size form of measurement is only used within the roofing and construction industries. Though you can use the measurement yourself to try to calculate the cost of re-shingling your homes, such tasks are usually best left to an experienced roofing contractor. Nonetheless, even if you have confidence in your ability to determine the correct amount of materials needed, there are still a few steps you should take before you try.

roof quotes online

Online Roof Measurements

What is roofing measurement tool?

Whether you’re installing shingles, metal, tile, composites, slate, shake, or commercial roofs, the Sky Roof Measurement Tool will increase your efficiency, helping you save time, increase sales, and grow your business. Scaling a ladder and crawling atop a roof can be time-consuming and hazardous.
 
The Area Calculator can be used to calculate the area of a variety of simple shapes that together can comprise the area of the roof. Using the aggregate area of these simple shapes can yield a more accurate roof area to be used with the Roofing Material Calculator.
 
Contractors will also be able to upload drone images or blueprints to measure. Once mapping is completed, the user receives a final, downloadable report on the area, pitch, direction, and edge lengths of the roof, which helps determine how much roofing material to purchase, the amount of time the project will take, and the total cost to the customer.

Roofing Tips: Roof Slope & Style

There are two main categories of roofing: sloped and flat. A flat roof has a slope of 2 in 12 or less. The run always remains constant at 12 inches. A low slope roof is anywhere from 2 in 12 to 4 in 12. Conventional slope roof range between 4 in 12 and 8 in 12. Anything more than 9 in 12 is considered steep. Steeper-sloped roofs are considered more aesthetically pleasing and last longer. These benefits do not come cheaply though. A 12 in 12 roof can cost up to 50% more than a 4 in 12 roof. This is because a steep-sloped roof requires a taller chimney and more lumber for framing. However, the end result may be well worth it as your roofing material is estimated to last up to 50% longer and will require less maintenance.

Roof styles or types are usually predesigned by the builder of your home. They determine what kind of materials you can have on the roof, due to the slope. The first option is a flat roof. This style is just like a long board across the top of your home. A gabled roof looks like two sides of a triangle. A shed roof is slanted down one way, either towards the left or right. Gambrel roofs resemble barn roofs. Finally, mansard roofs have a flat top with sides that lip over the top a little and hang over the home.

roof measurements

Satellite Roof Measurements: Features of a Roof Report

  • Accurate Roof Pitch Measurements
  • Roof Measurements including AreaRakesRidgesHips and Valleys, and every edge is separately measured and identified.
  • CAD style drawings with colored lines identifying every type of roof edge
  • Online access to your Roof Reports for your Employees, Subs and Suppliers with no software to install
  • Multiple image providers for over 98% coverage of the USA & Canada
  • Also supports file formats such as XML,RFX,DFX/DWG AND WRL
roof blueprint

How to Measure a Roof From the Ground

If you’re planning work on a roof and don’t have the building plans, taking preliminary measurements from the ground allows you to approximate the roof area and estimate some costs. Measuring hip roofs, dormer roofs or roofs on hillside homes from the ground requires experience and special equipment. But, you can measure a gable or flat roof from the ground with the help of an assistant.

Method 1: Counting asphalt shingles to measure your roof area from the ground.

Most asphalt shingles are three feet wide with three tabs. Each tab is got 5 inches of reveal. So by counting these in digital photos you can come up with pretty reliable dimensions. If there is any doubt on the shingle dimensions, you can calibrate the method by measuring a typical shingle in a lower, accessible location.

Method 2. Pythagorean Theorem.

Measure the horizontal run of the roof surface from the ground (‘a’ in the third figure below). Then count the number of shingles to the peak of the roof. Multiple the number of shingles times the width of each shingle (which you can measure at ground level) to get ‘b’ in the figure below. Then calculate the line length of the roof (‘c’ in the figure) using the Pythagorean Theorem; c = square root (a squared + b squared). It is also easy to calculate the roof angle by taking the inverse tangent of b divided by a.

With these simple tricks you can measure your roof area from the ground.  

Roofing Calculator

How Roof Pitch is Calculated

To accurately calculate the area of your roof, you must first determine its slope, or pitch. A roof’s pitch is determined by how much it rises vertically for every foot it runs horizontally. Thus, a moderate “6 in 12” roof pitch means that the roof rises 6 inches vertically for every 12 horizontal inches it runs. A “12 in 12” pitch is a steep, 45-degree angle roof. See the image below for more explanation on rise, run and pitch.

Three Easy Ways To Measure Your Roof’s Pitch

Pitch Measurement Method 1

Roof Pitch Calculator

1. On a ladder beside the roof, place the level a foot or so up the roof, hold it level, and measure from the 12-inch mark on the level’s bottom, straight down to the roof. If this distance measures 4 inches, you have a 4 in 12 pitch; 8 inches and you have an 8 in 12 pitch.

Pitch Measurement Method 2

Roof Calc

2. On a ladder at the gable end of your house, place the level against the gable trim, flat against the side of the house. Now measure from the 12-inch mark of the level up to the bottom edge of the gable trim. This distance is the roof’s rise.

Pitch Measurement Method 3

Roofing

3. In the attic, place the level against a rafter with the 12-inch mark on the bottom of the rafter. Measure from the end of the level up to the bottom edge of the rafter. That is the roof’s ris

 

roof blueprint

How To Measure Your Roof Using Google Earth

Each time you add points, the area will update and there is a box below that will convert this into acres, meters, kilometers, miles, and finally, square feet. It will also give you the perimeter of the shape of the roof.

Using this tool will be very helpful for you in finding out the acreage or the tract of land of your property. It will also give you the square footage of your roof and any other areas that you’re wanting to estimate. You can even embed this tool on a website that you own.

Call Us for Roof Measurements : (315) 926-1777 

OR  Email us : info@skyroofmeasure.com

While these tools are very helpful, there are a few variables that you’ll want to know. If you’re in a rural area, you may have to go with the cross streets as the address may not bring up what you’re looking for. In such areas, you may wind up using the GPS coordinates or a landmark to get to where you’re going.

Special precautions must be taken when measuring the area of a roof. The images that appear on google maps are often at a slight angle, which combined with the angle of a roof can cause errors. For this reason it is best to outline the roof at points which are all at the same elevation. On a simple house for instance you would only click on the corners of the roof and not on any points along the peak as that would cause an error. After measuring the area of the footprint you can estimate the actual roof area based on the angle of the roof. Similarly if you using the area calculator tool to measure a roof with multiple levels, you should do the individual section separately. The google maps area calculator is not 100% accurate. Do not rely on this tool as your only resource in making important decisions.

roof report

Without utilizing the proper tools, trying to determine the proper area of a residential or commercial roofing space can be difficult. With various different angles and pitches, it’s nearly impossible…

roof blueprint

Roof Measuring Services

What is a roof measurement?

Roof measurements are then used to quote any roofing job and completely eliminate the need to re-measure. For contractors, this means all members of your team (sales, production, installation, etc.) and the homeowner can be on the same page when it comes to the roofing job.

 

Our service is quick and easy to use.  Sign up for a free account today and ordering is as easy as 1, 2, 3!

  1. Enter the address where you need a measurement on the home page, and confirm the location on the satellite map view.
  2. Choose the type of report you need – commercial or single family home and/or wall report – and add any special instructions.
    • Add your reference number or claim ID to the order for easy tracking.
    • Let us know if you have special requirements, such as including secondary structures on single family home orders.
  3. Confirm your order and checkout.  You can also order multiple reports on a single invoice including an entire campus. 

Most customers pay by credit card.  Let us know if you need to pay by check.

OR Please email me here : ( info@skyroofmeasure.com ) and I will get back as earliest as possible…

Aerial Reports uses the best of the industry’s Proven off-the-shelf software and available aerial imagery to provide Roofers, Contractors, Insurance Carriers and Adjusters a Customized, Detailed and Accurate Roof Measurement Reports. Never miss another opportunity to provide an estimate due to distance, location and weather conditions.

What are drone roof measurements?

Drone Roof Measurements. When you have the need for closer inspection of a roof due to an inadequate or obstructed satellite image, drones can be a great asset. You can take pictures of any part of the roof, close-up and from any angle.
Satellite Roof Measurements: Features of a Roof Report Accurate Roof Pitch Measurements Roof Measurements including Area, Rakes, Ridges, Hips and Valleys, and every edge is separately measured and identified. CAD style drawings with colored lines identifying every type of roof edge
roof blueprint

Roof Measurements

Satellite Roof Measurement

One reason why measuring a roof by satellite is so accurate is due to the fact that you have as high and clear a vantage point as is possible. You can zoom in as much as you want, depending on the tool used, and everything is easy to see and put together. In other words, there’s no way to get any higher or see the roof from any better of an angle than from far above in a satellite.

Roof Measurements from Satellite

Another thing that helps to enhance the accuracy of satellite roofing measurements is the combination of pairing the satellite photos with software to help get the best and most accurate measurements possible. By starting with such good photos, strong software designed for the purpose can help ensure accurate measurements of the roof.

That’s why it’s so important to make sure you use the right software. Its accuracy will depend on its capabilities. But, it will also depend on its inputs. IN other words, one of the reasons why the satellite approach is so accurate is because it has fantastic inputs from the satellite photos. Otherwise, this accuracy wouldn’t be where it is.

Roof Measurements With Google Earth

  • On your computer, open Google Earth.
  • Search for a place, or select a location on the globe.
  • On the left, click Measure. . …
  • Click the map to set measurement points.
  • To remove a point, on the right, click Undo .
  • To complete your line measurement, double-click on your last point, or click Done .

How to Get Accurate Aerial Roof Measurements?

How to Get a Roofing Measurement
  1. Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area.
  2. Note any skylights, chimneys or other parts of the roof that would not require materials so you can subtract those measurements from your total area.

How do you measure a flat roof?

Just measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane. Simply add the square footage of each of the planes together to derive the total square footage of your roof. For example, this flat roof has one roof plane.

Rooftop Measurements

  • Prepare roof measurements and professional estimates from anywhere.
  • Print email and share digital reports with property owners or with your team. 
  • Eliminate unnecessary trips to the job site. 
  • Spend less time on roofs and more time with customers face-to-face.
  • Impress clients with new roof simulations, roof diagrams and other visuals.

How to Measure Roof Slope from On the Roof

To use the direct roof slope measurement procedure, in addition to safe access to a roof that won’t be damaged by touching or walking on it, you need: a tape measure and a carpenter’s level. This procedure to measure roof slope can be performed on the roof or from a ladder at roof edge. 

  • Hold the carpenter’s level in a horizontal position with one end touching the roof surface.
  • Measure out 12″ along the level bottom edge – the green line in our sketch. Mark this point on the leve.
  • Measure straight down to the roof surface from the mark you just made – the blue line in our sketch.
  • Read that distance in inches. The result is inches of rise per foot of run.

How to Manually Measure a Roof

  1. Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area.
  2. Note any skylights, chimneys or other parts of the roof that would not require materials so you can subtract those measurements from your total area.
  3. Add together the calculated square footage of each surface to get the figure for total square footage of the roof.
  4. After determining the total square footage of the roof, you must calculate the pitch of the roof by measuring the vertical distance (rise) over a 12 inch horizontal segment (run).
  5. Write down these numbers as the vertical measurement listed first and the horizontal measurement recorded second so you can find rise over run.
  6. When you have the total square footage and rise over run of the roof, you can calculate the roof squares to determine how much materials are needed to cover the roof. To calculate the number of squares on a roof, you need to divide its total square feet by 100.
satellite roof measurement

How Do You Measure a Roof Without Measuring It?

Roof surfaces are measured in “squares”. A roofing square is equal to 100 square feet of the roof. To determine the number of squares on the gable roof example in this post, divide its total of 2400 square feet by 100 (2400 ÷ 100 = 24). This means you would need 24 squares of shingles to cover that roof.

How do I calculate the size of my roof?

Multiply your house length by your house width to get the area. (For example, 40 feet x 30 feet = 1,200 square feet.) Next, multiply the area by your roof’s pitch. (1,200 x 1.05 = 1,260 square feet.)

aerial roof measurement

How to Measure a Roof From the Ground

Measure out from the face of the wall below the fascia or rafter tails to a point that aligns with the outer edge of the roof. Multiply this measurement by the length of the roof from end to end, and add this to the first result. Double the result to determine the total area of the roof at both sides.

How do you measure the pitch of a roof from the outside?

To measure the roof pitch, you’ll need an 18- or 24-inch level, a tape measure, and a pencil. First, measure 12 inches from one end of the level and make a mark. Then, in the attic, place the end of the level against the bottom of a roof rafter and hold it perfectly level.

Is the square footage of a house the same as the roof?

Square Footage of Your Roof:

So a trick to estimate your roof size is to multiply the square footage of your house by 1.5 (ex: A 2,000 square foot house will have a roof that is approximately 3,000 square feet).

How much does it cost to reroof a 1000 square foot house?

Average Cost to Replace a Roof by House Size
House (& Roof**) by Square FootRe-Roofing Cost*
1,000 (1,054)$4,000 – $5,500
1,100 (1,160)$4,200 – $6,000
1,200 (1,265)$4,500 – $6,500
1,500 (1,581)$5,500 – $8,000

How much is a square of shingles?

Shingles are sold by the bundle and by the square. A square is equal to 100 square feet and will cost anywhere between $100 and $1,800. A bundle is around 1/3 of a square and costs an average of $30 to $600.
roof quotes online

How many square feet are in a bundle of shingles?

Calculating the number of bundles, you need is simple if you are using shingles that come three bundles to a square. Each bundle covers 33.3 sq. ft. of roof area—which is close enough to the 32 sq.

How much does it cost to tear off and replace a roof?

On average, it costs from $1.20-$4 per square foot to tear off and replace a roof with asphalt shingles. For a 1,700-2,100 square foot ranch-style property, that costs about $1,700-$8,400. However, roof replacement costs increase when you use higher-end roofing materials.

Looking For a Roof Estimating Report??

Satellite roof measurements

Does Google Earth Have a Measuring Tool?

Google Earth is getting a new Measure tool today that will let you — you guessed it — measure the distance and area of things on the map. With the tool, users can measure the distance between two points or the surface area of a selected chunk of the map.

How do I find the land size on Google Maps?

Just navigate to the land you want to measure, click your way around the perimeter and the calculator below the map will tell you how many acres are within the perimeter you’ve established. Easy as that. You can also then export the area you’ve just drawn as a KML file and load that file onto Google Maps at any time.

Call Us +1 (940) 233-5566

Does Google Earth show property lines?

You can view parcel boundaries, or view property lines in Google Earth™ and other GIS applications via a familiar map view format and quickly digest key location intelligence information.

Is Google Earth Pro free?

Google Earth Pro on desktop is free for users with advanced feature needs. Import and export GIS data, and go back in time with historical imagery. Available on PC, Mac, or Linux. By installing, you agree to Google Earth’s Privacy Policy.

How do I measure using Google Earth Pro?

Take and save a measurement

  1. Open Google Earth Pro.
  2. Go to a spot on the globe.
  3. In the menu bar, click Tools. …
  4. In the bottom left, select Mouse Navigation.
  5. Click the tab for what you want to measure.
  6. On the map, hover over a spot and click a starting point for your measurement.

Why is Google Earth so blurry?

Check the status bar at the bottom of the image: If the status bar is at 100% and the image still looks blurry: We don’t have high-resolution data for this location. If the status bar is incomplete after several minutes: There may be an issue with your internet connection, firewall settings, or graphics card drivers.

How accurate is Google Earth elevation data?

A vertical accuracy study found the root mean square error (RMSE) of GDEM data is 8.68 meters when compared against 18,000 geodetic control points in the USA . LIDAR-derived elevation data are available for some coastal states and inland states at a resolution of 1/9 arc-second (about 3 meters)

How do I increase resolution on Google Earth?

Save image options in Google Earth Pro. You’ll find the save feature under file > save > save image. For a cleaner image, turn off all of the map options, and set the scaling to 1%. To maximize the saved image dimensions, set the resolution to maximum, and then resize the Google Earth window to a square.

What is the best version of Google Earth?

Choose the download that’s right for you

If you just want the basic Google Earth, this is the best option, because the in-browser version is speedy and readily accessible. However, we’re focusing on Google Earth Pro, a more versatile and complete option that’s designed to be downloaded to your desktop.

Residential Roof Estimation

How to Measure Area and Distance in Google Maps & Earth

Step One: 

You should start measuring by printing out a top view of your home. To do this, simply line up your house and click on the top corner to print.

Step Two:

  1. Frame your home back to the top shot. NOTE: You’ll want to be directly above and zoomed in as much as possible.
  2. Click the ruler icon on the left side of your screen.
  3. Switch the unit of measurement to feet.
  4. Click on a starting and stopping point, and you’ll get an estimated measure of distance.
  5. Start logging in your measurements.

Step Three: 

When complete, you’ll have a general idea of the size of your roof to send to a metal roofing supplier for an estimate.

Google Earth also offers a perimeter for the shape of the area that you can use to measure out the edges or area of a lawn, fencing, yard, the roof and more. As long as you keep in mind that these are only the most basic of guidelines, you’re going to be okay in your calculations. Since you’re using Google you’ll have to factor in any changes that may have been made since the satellite pictures have been taken and remember that the slightest changes may not be yet showing on your pictures.

Once you have a basic starting point you can go from there and make the necessary adjustments to have an accurate reading of the roof shape and size and factor in any other necessary adjustments that need to be made on your calculation.

Measure a roof with google earth –

What is Google Earth Pro?

Google Earth Pro is a desktop application originally designed to let you “travel the world without ever leaving your seat.” It allows you to experience both aerial and drilled-down street views of 3D cities through your web browser. Intended for touring and map building, it lets you import and export GIS data and view locations captured across various points of their history. As our valuation experts discovered, these very features can also be extremely useful for gathering and confirming property details needed for a statement of values analysis, virtual valuation and more — particularly when travel and access to sites are limited.

roof blueprint

Roofing Measurements

Your roof is a major structural component of your home, and a successful reroofing project requires a large investment in both time and money. Since you cannot afford mistakes during installation, we highly recommend you hire a professional contractor. 

                                 Call Us – (315) 926-1777

Estimating Shingles and Square Footage

If you’re intending on doing a shingle roof, you’re going to need to consider exactly how many shingles you will need to procure. To do this, you’ll need to assess the total square footage of your roof’s total surface. Doing so is straightforward. You or your hired roofing team will initiate by evaluating the span and width of each plane of the roof, adding to any dormers. Multiply the entire length by the width to receive the exact square footage of each plane. In the end, tally the roof’s full square footage by summing the square footage of each plane together.

Every roof surface is surveyed in “squares.” A square is purely any area of roof which computes at an exact 100 square feet. You’ll need to find out the number of squares on a roof in order to learn the number of shingles you’ll need to cover the roof. Let’s say you have a gable roof that is a sum of 24,000 square feet. Simply divide the entire square footage by 100. You’ll get a result of 240, meaning that you’ll need 240 squares of shingles to cover the roof.

How to Manually Measure a Roof

  1. Measure the width and length of each plane of the roof (including dormers), and then multiply those numbers to get the correct figure for the square footage of that area.
  2. Note any skylights, chimneys or other parts of the roof that would not require materials so you can subtract those measurements from your total area.
  3. Add together the calculated square footage of each surface to get the figure for total square footage of the roof.
  4. After determining the total square footage of the roof, you must calculate the pitch of the roof by measuring the vertical distance (rise) over a 12 inch horizontal segment (run).
  5. Write down these numbers as the vertical measurement listed first and the horizontal measurement recorded second so you can find rise over run.
  6. When you have the total square footage and rise over run of the roof, you can calculate the roof squares to determine how much materials are needed to cover the roof. To calculate the number of squares on a roof, you need to divide its total square feet by 100.
Slope –
Slope is the incline of the roof expressed as a ratio of the vertical rise to the horizontal run, where the run is some portion of the span. This ratio is always expressed as inches per foot.
 

Pitch –

Pitch is the incline of the roof expressed as a fraction derived by dividing the rise by the span, where the roof span is the distance between the outside of one wall’s top plate to another.

roof quotes online

Roof Measurements From Satellite

Aerial Measurements For Roofing Contractors and using Google Maps to get unlimited roof measurements can help any roofing contractor, and be more efficient. Most roofers feel like they need to go to every estimate and then measure the roof, and most of the time it’s a good idea to go to every estimate, but this free tool will give you the opportunity to do a little homework before you get to the job.

                            Call Us – (315) 926-1777

Satellite Roof Measurements 

Our  roofing contractors are able to receive measurements of any roof in a very short time with extreme accuracy without the need to visit your home or business. Our aim is to provide you with all the necessary information to enable you to make informed decisions. 

Saving Precious Time

It also happens that roofing issues can sometimes become roofing emergencies so utilizing satellite roof measurements can speed up the process of repairing your roof. There is no need to book appointments in advance to have our roofers visit your home in order to physically take measurements and conduct calculations in order to provide you with an accurate estimate. Our foam roofing experts receive all your roofing measurements electronically and prepare your free no-obligation estimate in the shortest time possible.

How Satellite Information Is Received 

Satellite roof measurements are based on satellite images sourced from Google application programming interfaces (APIs) that receive information and images from Google Earth. The information and images are used to calculate accurately both the square footage and slope of your roof. It is no longer necessary to have individuals climbing on your roof to take physical and time-consuming measurements.

The Roof Measurement Report provides a detailed analysis of your roof layout and all the critical dimensions. Our full color report provides the detailed lengths, pitch and areas of every surface plane and edge. This report saves your time and enables accurate roof estimates for a roof repair or replacement. This is a professional grade report used for use by licensed roofing contractors or insurance companies. You will receive the report in .PDF format by email within 1-3 days.

What factors determine the price of a roof?

Type of Roofing  –  The material type that you purchase for your roof affects the bid price. There is a basic 3 tab or 3 in 1 style, Architectural or Laminated (Most Common) and then you designer or premium level shingles. Each of the major manufacturers will have their own individual characteristics, the thicker the shingle the heavier it will be rated for durability.

Pitch – The steeper the roof the steeper the price! Steeper roofs require additional safety precautions and create slower installation speeds. This additional labor required will add to the total cost of the job.

Height – Similar to the roof’s pitch affect on price, the higher the roof typically the higher the price. Most companies will charge an additional amount for 2 or 3 story access.

Allowance For Growth And Change

Since technology has thrived over the past few years and is consistently growing and changing, using satellite imagery allows for the ability of homeowners and contractors to grow and change with reducing risk and potential damages that could occur when obtaining roof measurements. In addition by getting more accurate readings and measurements on the roofs, the expenses that are required are reduced as they are more accurately acquired and they take fewer visits to obtain the calculation or measurements. In addition, satellite measurements have the ability to give homeowners the exact square footage even though the slopes and steeps of the home. This can increase contractors companies proficiency and accuracy to help homeowners increase the longevity of their homes because the repairs will be done more professionally. Moreover, contractors and homeowners can measure roof from a satellite for free with the programs that are available online, thus saving them time, claims, flexibility, and materials for roofing jobs.